工業用スクリュー電動600v25aワイヤコネクタ端子台-端末

包装

仕様

  Application of terminal fittings

HUK series combination type terminal block has a complete range of accessories. Through the use of foundation and convenient small, easy to install the accessories, the series of products for all intents and meet the requirements of various circuit wiring the desire to be able to save a space already practical way to realize. In addition to the use of methods and implementation of various typical attachment function diagram, other accessories in the product introduction has its unique advantages.

All kinds of accessories in structure design to take full account of the convenience and safety of various circuit requirements and use, when a thin terminals to achieve more than two function will have several attachments with to realize.

Center contact piece for connecting adjacent terminals formed contact terminal group, each of the 10 is a group, arbitrary separation, can also add short piece to achieve 10 above the contact combination, with insulating sleeve, screws and fastening terminal to the gasket.

The side in contact is central to meet the other terminal function and can not connect with tapered connection hole connected to form a contact terminal group mode. Because it has to be pressed on the wire connecting space below but reduction of a wire section level, each of the 10 pole can be separated, back with plastic insulation layer to prevent electric shock.

Grouping separator for separating the terminal group, according to the dual effect of grouping visual and electrical isolation.

The plug has 2.3 and 4 two specifications and the corresponding (installed in the electronic conductive central screw hole) test socket forming test connection, can be all kinds of electrical parameter measurement of terminal blocks at run time. The plug handle has eight colors available for selection.

Tags for marking the terminal in the terminal sequence or position of wires in the corresponding circuit connection point symbol. Each of the 10 bit, can cross vertical printing digital and letters or other marking content, the terminals are assembled rows after rapid installation in the upper part of the tank at the two ends of the mark.

Insulating spacer for the adjacent contact terminal set grouping and electrical isolation. All the contact terminal group must be installed at both ends of the insulating spacer, the terminal block assembly after the insertion, will not affect the overall space.

Characteristic.

1.Installation structure design is reasonable, does not need the additional spring card version, only by reasonable design structure in nylon material flexibility, convenient installation in the G type or T type guide rail, strong versatility, more than 50 cubic meters by reinforcing and accessories installation.

2.UKL series combined terminal has the advantages of small volume, specifications of all varieties, can be connected with the characteristic of large conductor cross section.

3.Terminal of the series of row of good conductivity, below 50 cubic meters by using the copper reduction box screws and fastening with copper, 50 cubic meters of copper wire frame and the copper screws, tighten force.

Safety use

1.A straight line that the wire box bottom surface very fine can also be pressed;

2.Can the indentation conductive sheet on the oxide layer cut the wires on the possible implementation of good electrical connection;

3.Terminal design has the self-locking function, prevent the screw natural removal, ensure the earthquake resistance of the terminal.

4.Insulation material quality, reasonable design, both to ensure the environment is to ensure the personal safety.

5.Use high-quality nylon insulation materials, various indexes such as abnormal heat resistance, tracking resistance index, alternating hot properties, heat resistance are to meet or exceed the requirements of IEC60947-7-1 standard, and flame retardants containing no halogen, combustion does not produce Yin corrosive acid oxide.

6.Live parts are installed in the insulating parts, assembled into a row of the operator's hands do not touch the charged body, ensure the safety of the people.

TB series modular terminal row

Product overview

1.TC series is plate screw with low pressure closed integral structure, rated voltage 600 v.
2.The rated current is divided into: 15A.25A.35A,45A,60A,100A,6kinds of specifications.
3.Can connect wire section 0.5-22 mm2, this product is simple in structure, convenient installation, firm and reliable.

4. Using flame retardant VO level PC (polycarbonate) plastic base, screw tolerance increased after heat treatment, not smooth silk. 

5.   Screw with special processing after the salt mist in the general case, can not be rust corrosion for a long time.

Another use stainless steel screws, for in long term high acidity and maritime career dedicated.
This company produces the TB series terminal, through environmental certification and CE certification.

Install and use

This product can be directly on the base plate punching installation, installation dimensions refer to the said purpose.

If you have any questions, please contact with us :

http://webatm.alibaba.com/atm_chat.htm?enemberId=enaliintxawmdq

about the certification

お取引の流れ→(詳細を確認こちらをクリツク！)